Monday, 20 July 2015
Tuesday, 30 June 2015
Recrystallisation procedure and requirements
Recrystallisation
Introduction: Recrystallisation is a simple procedure in which we can separate a water soluble pure compound from insoluble impurities
Requirements
- Porcelain bowl
- Bunsen burner
- Wire gauze
- Water soluble salt
- Water insoluble impurities
- Weighing balance
- Stirrer
- Filter Paper
- Funnel
- Conical flask
Procedure
- Take a fixed mass of pure water soluble compound in the porcelain dish
- Add a fixed mass of insoluble impurity
- Mix thoroughly
- Add water
- Stir properly to make sure all the soluble salt dissolves
- Next, heat the porcelain dish over a bunsen burner taking care to put a wire gauze between the dish and the flame
- When the mixture starts boiling pour it through the filter paper (which has to be placed in the funnel) into the conical flask
- If you still see traces of the impurity repeat step 6 and 7
- Keep doing so until you get a clear filtrate
- Next cool the solution until crystals form
- Collect the crystals and weigh them
- Compare it to the original mass
Friday, 19 June 2015
Tuesday, 16 June 2015
Group 4 project
Recently, in school we had our Group 4 project. The project combines all the subjects of the group 4 of the IB diploma. You perform the project along with your peers who have taken different group 4 subjects. It is a required part of the IB Diploma.
So, initially you will be given an overarching topic to do the project on. In our school the overarching topic was "water". This is quite a relevant and interesting topic considering the crisis of water shortage. Hence, it is quite easy to take international mindedness into consideration while performing a project on this topic. Then you have to choose a topic under this broad topic. For example, my group decided to do "water in an industry".
The next step in the Group 4 project is to decide which experiments to perform in each subject. Each experiment must be linked to your topic and have some real world significance. Also, every member of the group should be familiar with each experiment in every science. This means a Biology student should have thorough knowledge and an Environmental Studies student should be able to answer any question about the Chemistry experiment. The beauty of the Group 4 project is that you end up learning a bit about each and every science. In fact, our school had a session in which we learnt basic experimental skills in each science and I recommend any teacher reading this to do the same for his/her student as I found this very useful in integrating all the sciences.
At the end of the Group 4, you will need to write a reflective statement which is digitally sent to the IB. It is only 50 words and you should sum up your experience. Here is a sample reflective statement:
"The topic for our group 4 this year was water and my group’s topic was water in an industry. The group 4 project was an amazing experience and I learnt a lot about Physics, Chemistry, Biology and ESS."
P.S. For this project, I performed recrystallisation and in my next post, I will include the procedure and pictures for a recrystallisation experiment.
So, initially you will be given an overarching topic to do the project on. In our school the overarching topic was "water". This is quite a relevant and interesting topic considering the crisis of water shortage. Hence, it is quite easy to take international mindedness into consideration while performing a project on this topic. Then you have to choose a topic under this broad topic. For example, my group decided to do "water in an industry".
The next step in the Group 4 project is to decide which experiments to perform in each subject. Each experiment must be linked to your topic and have some real world significance. Also, every member of the group should be familiar with each experiment in every science. This means a Biology student should have thorough knowledge and an Environmental Studies student should be able to answer any question about the Chemistry experiment. The beauty of the Group 4 project is that you end up learning a bit about each and every science. In fact, our school had a session in which we learnt basic experimental skills in each science and I recommend any teacher reading this to do the same for his/her student as I found this very useful in integrating all the sciences.
At the end of the Group 4, you will need to write a reflective statement which is digitally sent to the IB. It is only 50 words and you should sum up your experience. Here is a sample reflective statement:
"The topic for our group 4 this year was water and my group’s topic was water in an industry. The group 4 project was an amazing experience and I learnt a lot about Physics, Chemistry, Biology and ESS."
P.S. For this project, I performed recrystallisation and in my next post, I will include the procedure and pictures for a recrystallisation experiment.
Friday, 20 March 2015
Sunday, 8 March 2015
Useful Links and Resources for IB Chemistry
Chemistry -IBDP
Chemistry Data Booklet
IB Experiments and Investigations
Chemistry for use with the IB Diploma Programme Higher Level
IB Interactive Guide
Guidance for IA
IA Chemistry checklist
Titration
Titration is interesting because it gives you the exact volume of a base required to neutralise a particular volume of an acid. The process for titration is actually simple and anyone can try it in a chemistry laboratory.
So basically, you need:
- 25 ml burette
- 25ml pipette
- Dilute acid
- Dilute alkali/base
- Phenolphthalein
Now, I'm going to move on to how to do the experiment i.e. the procedure
- So the first thing you should do is rinse both the burette and the pipette. To do this, for the burette, you can shut the stopper and then pour some sodium hydroxide (NaOH) into the burette. Put your thumb over the other end. Then shake it making sure it flows through the entire burette and then dispose of the sodium hydroxide in a sink. Similarly, rinse the pipette but use dilute hydrochloric acid (HCl).
- Next, fill the burette up to 25 ml with your dilute base and take 25ml of acid in the pipette.
- Next, pour the acid into a beaker below the burette containing the base.
- Add on drop of phenolphthalein to roughly the centre of the acid.
- Now, add the alkali one drop at a time. The phenolphthalein should turn purple/pink and then shake the beaker to get rid of this colour.
- Repeat the above step till the purple colour doesn't disappear on shaking.
- See the range of volume of the base added for which the purple colour doesn't disappear (e.g. 11-12ml).
- Now, repeat the experiment but add 1 ml at a time between the range of volume for which the colour stopped disappearing to get the exact value.
Subscribe to:
Posts (Atom)
